Botanical Extract Specifications in 2026: Six Numbers That Decide Whether a Quote Is Real

share:
November 18,2026

Botanical Extract Specifications in 2026: Six Numbers That Decide Whether a Quote Is Real

Most botanical extract quotations look the same: a product name, a percentage, a price per kilogram and a lead time. The differences that matter sit in the six numbers usually left out of the email. This guide uses a real standardized product - Andrographis paniculata extract at 20% andrographolide - to show what a complete specification looks like, and why each figure changes what you can legally print on a label.

1. The assay, and the method behind it

"20% andrographolide" is a claim about a number and a technique. HPLC against a reference standard is the defensible baseline; a UV reading or a "by calculation" figure can land within a few points of the same number on paper while describing a different material. Ask for the method line and the batch result side by side. A well-documented lot reads like this: specification min. 20.0%, batch result 20.21%, method HPLC.

If the certificate shows a specification column and a result column that are identical in every row, you are looking at a template, not a batch record.

2. Extract ratio versus concentration factor

Buyers routinely confuse the two. The drying ratio describes how much fresh plant becomes how much dried material; the extract ratio describes how much dried material becomes how much extract. For this product the drying ratio is 3:1, the extract ratio is 20:1, so the concentration factor is 60. That single number explains the price, the dosage and the color: a 60-fold concentrate cannot be substituted with a 10:1 powder without reformulating.

When a supplier quotes "20:1" without stating which ratio applies to which step, the figure is decorative.

3. Carrier and composition disclosure

Standardized extracts are rarely 100% extract. This product is declared as not less than 98% extract with silicon dioxide at not more than 2% as carrier. That matters for three reasons: the assay is calculated on the finished powder, the carrier appears in your own ingredient statement, and a change from 2% to 10% carrier silently dilutes everything else while leaving the headline percentage intact. Demand a composition table, not a single number.

4. The physical numbers that decide whether the line runs

Particle size, bulk density, loss on drying and ash are the figures production notices first. A powder specified at minimum 95% through 80 mesh and delivered at 99% fills capsules at a predictable weight; one that arrives at 70% passing does not. Bulk density at 0.52 g/ml against a minimum of 0.3 tells an encapsulation engineer more about throughput than any brochure. Loss on drying at 4.07% against a maximum of 7.0%, and ash at 6.91% against a maximum of 10.0%, show a lot with margin rather than a lot scraped through the limit.

5. Metals and microbiology as individual limits

A single line reading "heavy metals max. 10 ppm" is not a specification your quality team can release against. Individual limits are what auditors expect: lead max. 2 ppm, arsenic max. 1 ppm, cadmium max. 1 ppm, mercury max. 0.1 ppm, each with its own reported result. The same applies to microbiology - total plate count, mould and yeast, and negative results for E. coli, Salmonella and Staphylococcus, each stated separately. A batch reporting 160 cfu/g total plate count against a 10,000 cfu/g limit is a comfortable release, not a borderline one.

6. The document pack behind the certificate

For EU-bound shipments in particular, the COA is only one page of the file. A complete pack for a leaf-derived extract typically includes an allergen statement covering the 14 major allergens, non-GMO status with the applicable regulations cited, confirmation that no ethylene oxide was used, BSE/TSE-free and vegan suitability statements, PAH4 and benzo(a)pyrene limits, pesticide residue compliance, residual solvent declaration, pyrrolizidine alkaloid limits, and nitrosamine status. Where a supplier cannot produce these, the buyer inherits the work - usually two weeks before a customer audit.

7. Certificates: held, or in progress

Distinguish the two in writing. A supplier applying for ISO 22000 is not a certified site, and the difference belongs in your supplier qualification file rather than in a marketing paragraph. Kosher and Halal certificates that are actually held should be supplied as copies with valid dates, not as logos.

8. A short checklist to send with the next RFQ

  • Assay value, method and reference standard

  • Drying ratio, extract ratio and concentration factor

  • Composition table including carrier percentage

  • Particle size, bulk density, loss on drying, ash

  • Individual heavy metal limits with batch results

  • Microbiology as separate limits and results

  • Allergen, non-GMO, ETO, BSE/TSE, PAH and solvent statements

  • Certificates held versus in progress, with document copies

None of this is exotic. It is the difference between a quotation and a purchase order that survives an audit.

Further reading

Reading a Botanical Extract COA: A B2B Buyer's Quality Checklist for 2026

Andrographis Paniculata Extract 20% Andrographolide: specification and batch data

2026 Plant Extract Sourcing Trends: A B2B Buyer's Guide to Botanical Ingredient Suppliers

Request a specification pack

For a worked example of everything above, contact the UNIWELL sales team at info@uniwellbio.com and request the Andrographis 20% specification sheet together with the current batch COA.

LET’S CREATE YOUR PREMIUM BOTANICAL INGREDIENT SOLUTIONS

Have a project in mind? Share your requirements — we’ll turn your ideas into reliable products.